一体化航天伺服机电组件用行星滚柱丝杠研究

微特电机 ›› 2021, Vol. 49 ›› Issue (5): 31-33.

一体化航天伺服机电组件用行星滚柱丝杠研究

彭之春¹, 徐克¹, 孙耀程²

1.中国航天科工南京晨光集团,南京 210012;
2.中国电子科技集团公司第二十一研究所,上海 200233

收稿日期:2020-12-07 出版日期:2021-05-28 发布日期:2021-06-09

Research on Planetary Roller Lead Screw Applied to Integrated Aerospace Servo Electromechanical Components

PENG Zhi-chun¹, XU Ke¹, SUN Yao-cheng²

1. China Aerospace Science & Industry Nanjing Chenguang Group, Nanjing 210012, China;
2. No.21 Research Institute of CETC, Shanghai 200233, China

Received:2020-12-07 Online:2021-05-28 Published:2021-06-09

摘要/Abstract

摘要： 根据小型化、高可靠、高强度、高刚度要求,设计了应用于一体化航天伺服机电组件的RV10×2行星滚柱丝杠。根据航天舵机的实际工况,对航天舵机机电组件用行星滚柱丝杠的综合性能评价方法进行研究,并应用综合性能评价方法对RV10×2行星滚柱丝杠进行试验,符合设计要求,应用RV10×2行星滚柱丝杠的机电组件已通过总体的各项试验,验证了该行星滚柱丝杠应用综合性能评价方法的有效性。

关键词: 行星滚柱丝杠副, 综合性能评价方法, 螺纹精度检测

Abstract: According to the requirements of miniaturization, high reliability, high strength and high stiffness,RV10×2 planetary roller screw used in integrated aerospace servo electromechanical components is designed.According to the actual working condition of aerospace steering gear, the comprehensive performance evaluation method of planetary roller lead screw for electromechanical components of aerospace steering gear is studied, and RV10×2 planetary roller lead screw is tested by comprehensive performance evaluation method, which meets the design requirements. In addition, the electromechanical components of RV10×2 planetary roller lead screw have passed the overall tests meet the requirements, which verifies the effectiveness of the comprehensive performance evaluation method for planetary roller screw.

Key words: planetary roller screw pair, comprehensive performance evaluation method, thread accuracy test

中图分类号:

TM305

彭之春, 徐克, 孙耀程. 一体化航天伺服机电组件用行星滚柱丝杠研究[J]. 微特电机, 2021, 49(5): 31-33.

PENG Zhi-chun, XU Ke, SUN Yao-cheng. Research on Planetary Roller Lead Screw Applied to Integrated Aerospace Servo Electromechanical Components[J]. Small & Special Electrical Machines, 2021, 49(5): 31-33.

[1]	王晓远,高鹏,赵玉双.电动汽车用高功率密度电机关键技术[J].电工技术学报,2015,30(6):53-59.
[2]	沈启平.车用高功率密度永磁伺服同步电机的研究[D].哈尔滨:哈尔滨工业大学,2012.
[3]	王继强,王凤翔,鲍文博.高速永磁电机转子设计与强度分析[J].中国电机工程学报,2005,25(15):140-145.

[1]	程荣, 余光辉. 中走丝线切割机在小模数齿轮加工中的应用[J]. 微特电机, 2020, 48(11): 59-61.
[2]	董华兴, 何洪军, 高哲. 金属紧固件涂覆工艺改进设计[J]. 微特电机, 2020, 48(9): 60-62.
[3]	葛世昀. 绕线对电枢轴与换向器的配合浅析[J]. 微特电机, 2020, 48(6): 61-63.
[4]	吕欢剑. 取向磁场在铁氧体多极磁环制造中的运用分析[J]. 微特电机, 2020, 48(2): 1-4.
[5]	冯旭,章晨,王永艳. 双酚A型环氧树脂中二氧化硅的分散性研究[J]. 微特电机, 2020, 48(2): 60-62.
[6]	. 仿真分析微铣刀破损失效的影响因素[J]. 微特电机, 2019, 47(9): 69-72.
[7]	卢双,刘亚龙,王雨星,李艳芳. 基于有限元分析的表贴式磁性转子工艺技术研究[J]. 微特电机, 2019, 47(1): 87-90.
[8]	严亮, 王学彬, 高家鑫. 切削低膨胀环氧刀具选择与切削参数优化[J]. 微特电机, 2018, 46(12): 82-84.
[9]	肖洪波. 叠压铆压工装在风机部件制造中的应用[J]. 微特电机, 2018, 46(9): 87-91.
[10]	肖洪波. 交流风机内定子铁心制造的模具工艺保证[J]. 微特电机, 2018, 46(7): 86-90.
[11]	王学彬, 严亮, 杨健, 肖渊海. 临界厚度现象对微铣刀磨损的影响[J]. 微特电机, 2021, 49(2): 53-55.