阶梯形转子对双定子磁通反向电机齿槽转矩的影响

摘要/Abstract

摘要： 针对双定子磁通反向电机存在齿槽转矩过高,引起噪声振动的问题,采用阶梯形转子代替传统转子来削弱齿槽转矩。基于磁共能法,推导了双定子磁通反向电机齿槽转矩的解析模型,解释了阶梯形转子抑制齿槽转矩的原理。应用有限元方法,分别研究了各层阶梯块极弧系数对齿槽转矩和反电动势的影响。以齿槽转矩最小、反电动势谐波最小、反电动势幅值最大为综合优化目标,采用遗传算法,对不同层阶梯块的参数进行优化。结果表明,优化后的电机齿槽转矩降低了95.7%,额定负载时转矩波动从32%降低到2.4%,而平均转矩只下降了14.5%。

关键词: 双定子磁通反向电机, 阶梯形转子, 齿槽转矩, 遗传算法

Abstract: Aiming at the problems of high vibration and noise caused by high cogging torque in double stator flux reversal machine(DS-FRM), the method of using stepped rotor instead of traditional rotor to reduce cogging torque was investigated. An analytical expression of cogging torque for DS-FRM was derived based on co-energy method, the reasons for the reduction of cogging torque by using stepped rotor was explained based on the cogging torque expression. The influence of the width of each layer of the stepped rotor on the cogging torque and back electromotive force were investigated respectively by using finite element method. Multi-objective optimization of the parameters of different stepped blocks by genetic algorithm was used to achieve the smallest cogging torque, the smallest back-EMF harmonic, and the largest back-EMF amplitude. The results indicate that the optimized cogging torque is reduced by 95.7%, the torque ripple at rated load is reduced from 32% to 2.4%, while the average torque is only reduced by 14.5%.

Key words: double stator flux reversal machine(DS-FRM), stepped rotor, cogging torque, genetic algorithm

中图分类号:

TM352

邹定琛, 曹江华. 阶梯形转子对双定子磁通反向电机齿槽转矩的影响[J]. 微特电机, 2021, 49(3): 11-16.

ZOU Ding-chen, CAO Jiang-hua. Effect of Stepped Rotor on Cogging Torque of Double Stator Flux Reversal Machine[J]. Small & Special Electrical Machines, 2021, 49(3): 11-16.

参考文献

[1] 程明,张淦,花为.定子永磁型无刷电机系统及其关键技术综述[J]. 中国电机工程学报,2014,34(29):5204-5220.
[2] WANG C,NASAR S A,BOLDEA I.Three-phase flux reversal machine(FRM)[J]. IEE Proceedings of Electric Power Applications,1999,146(2): 139-146.
[3] ZHU Z Q, WU Z Z, EVANS D J,et al.Novel electrical machines having separate pm excitation stator[J]. IEEE Transactions on Magnetics, 2015,51(4):1-9.
[4] VAHAJ A A, RAHIDEH A, LUBIN T. General analytical magnetic model for partitioned-stator flux-reversal machine with four types of magnetization patterns[J]. IEEE Transactions on Magnetics, 2019,55(11):1-21.
[5] KIM T H,CHOI S K,REE C J,et al.Effect of design variables on irreversible permanent magnet demagnetizatization in flux-reversal machine[C]// Proceedings of 2005 International Conference on Electrical Machines and Systems.Nanjing,China:IEEE,2005:258-260.
[6] SHIN H K,KIM T H,KIM C J.A study on irreversible permanent magnet demagnetization in flux-reversal machines[C]//Proceedings of 2011 International Conference on Electrical Machines and Systems.Beijing,China:IEEE,2011:1-4.
[7] 张颖博,李洋.磁通反向永磁电机齿槽转矩分析与抑制[J].微电机,2019,52(10):31-35,54.
[8] 江胜军,胡余生,陈彬.永磁同步电机齿槽转矩优化方法分析[J].日用电器,2017( 11) : 55-57,61.
[9] 贺建忠.永磁同步电机齿槽转矩分析及削弱措施[J]. 科技创新与应用,2017( 3) : 162-163.
[10] VAKIL G,UPADHYAY P,SHETH N,et al. Torque ripple reduction in the flux reversal motor by rotor pole shaping and stator excitation[C]// International Conference on Electrical Machines and Systems.Wuhan,China:IEEE,2008:2980-2985.
[11] KIM Y S,KIM T H,KIM Y T,et al. Various design techniques to reduce cogging torque in flux-reversal machines[C]// International Conference on Electrical Machines and Systems.Nanjing,China:IEEE,2005:261-263.
[12] 寻志伟. 磁通反向电机齿槽转矩的削弱及其对电磁转矩影响[D]. 天津: 天津大学,2007.
[13] 赵维友. 磁通反向式电机齿槽转矩削弱方法的研究[D].天津: 天津大学,2007.
[14] WU Z Z, ZHU Z Q. Partitioned stator flux reversal machine with consequent-pole PM stator[J].IEEE Transactions on Energy Conversion, 2015,30(4):1472-1482.
[15] ZHU X F,HUA W.An improved configuration for cogging torque reduction in flux-reversal permanent magnet machines[J].IEEE Transactions on Magnetics,2017,53(6):8102504.
[16] CHUNG S U,LEE H J,HWANG S M.A novel design of linear synchronous motor using FRM topology[J]. IEEE Transactions on Magnetics,2008,44(6):1514-1517.
[17] BOLDEA I,WANG C X,YANG B,et al.Analysis and design of flux-reversal linear permanent magnet oscillating machine[C]// Conference Record of 1998 IEEE Industry Applications Conference.Thirty-Third IAS Annual Meeting.St. Louis,USA:IEEE,1998:136-143.
[18] 赵静,严雅霜,陈浩,等.转子齿形状对10极12槽开关磁通电机转矩特性的影响[J].电机与控制学报,2016,20(3):51-56.
[19] 景弋洋,章跃进.半闭口槽平行充磁永磁电机全局解析法优化设计[J].微特电机,2018,46(4):11-15.
[20] 于力. 基于遗传算法的中小型同步电机优化设计[D].长沙:湖南大学,2007.