中走丝线切割机在小模数齿轮加工中的应用

微特电机 ›› 2020, Vol. 48 ›› Issue (11): 59-61.

中走丝线切割机在小模数齿轮加工中的应用

程荣, 余光辉

中国电子科技集团公司第二十一研究所,上海 200233

收稿日期:2020-07-27 出版日期:2020-11-28 发布日期:2020-11-24
作者简介:程荣(1987—),男,工程师,研究方向为微小型齿轮减速器工艺优化。

The Application of Middle Thread Cutting Machine in Small Modulus Gear Machining

CHENG Rong, YU Guang-hui

No.21 Research Institute of CETC, Shanghai 200233, China

Received:2020-07-27 Online:2020-11-28 Published:2020-11-24

摘要/Abstract

摘要： 对电火花线切割机的种类和加工方式进行了对比,研究发现,在多品种小批量小模数齿轮加工时,中走丝电火花线切割机和多次切割的加工方式最合适,能满足齿轮制造时在质量、效率和成本上的要求。

关键词: 中走丝, 线切割, 多次切割, 小模数齿轮

Abstract: The types and processing methods of electric discharge machine (EDM) wire-cutting machine were compared, and it was found that the middle-wire-threading EDM wire-cutting machine and multi-cutting processing method were the most suitable for the multi-variety small-batch and small-modulus gear processing, which could meet the requirements of quality, efficiency and cost in gear manufacturing.

Key words: middle speed wire-cut machine, wire-electrode cutting, multiple cutting, small module gear

中图分类号:

TM305.1

程荣, 余光辉. 中走丝线切割机在小模数齿轮加工中的应用[J]. 微特电机, 2020, 48(11): 59-61.

CHENG Rong, YU Guang-hui. The Application of Middle Thread Cutting Machine in Small Modulus Gear Machining[J]. Small & Special Electrical Machines, 2020, 48(11): 59-61.

[1]	熊达.中走丝电火花线切割机的特点与发展趋势[J].山东工业技术,2018(11):55.
[2]	钟健.数控电火花线切割中走丝加工技术分析[J].湖北农机化,2019(18):141.
[3]	贾志新,刘译允,高坚强,等.往复走丝电火花线切割多次切割工艺试验[J].电加工与模具,2016(1):55-58.

[1]	卢双,刘亚龙,王雨星,李艳芳. 基于有限元分析的表贴式磁性转子工艺技术研究[J]. 微特电机, 2019, 47(1): 87-90.
[2]	肖洪波. 叠压铆压工装在风机部件制造中的应用[J]. 微特电机, 2018, 46(9): 87-91.
[3]	肖洪波. 交流风机内定子铁心制造的模具工艺保证[J]. 微特电机, 2018, 46(7): 86-90.
[4]	王学彬, 严亮, 杨健, 肖渊海. 临界厚度现象对微铣刀磨损的影响[J]. 微特电机, 2021, 49(2): 53-55.