多自由度平面感应电机发展综述

doi:1004-7018-46-8-88-92

微特电机 ›› 2018, Vol. 46 ›› Issue (8): 88-92.doi: 1004-7018-46-8-88-92

多自由度平面感应电机发展综述

吴伟¹,司纪凯¹,岳帅军¹,刘群坡¹,封海潮¹,李应生²

^1. 河南理工大学,焦作 454003
^2. 郑州润华智能设备有限公司,郑州 450001

收稿日期:2017-03-21 出版日期:2018-08-28 发布日期:2018-08-28
作者简介:吴伟(1992—),男,硕士研究生,研究方向是特种电机理论与应用。
基金资助:
国家自然科学基金项目(51777060,51277054);河南省自然科学基金项目(1623004117)

An Overview on Development of Multi-Degree-of-Freedom Planar Induction Motor

WU Wei¹, SI Ji-kai¹, YUE Shuai-jun¹, LIU Qun-po¹, FENG Hai-chao¹, LI Ying-sheng²

^1. Henan Polytechnic University,Jiaozuo 266300,China
^2. Zhengzhou Runhua Intelligent Equipment Co.,Ltd.,Zhengzhou 450001,China

Received:2017-03-21 Online:2018-08-28 Published:2018-08-28

摘要/Abstract

摘要：

多自由度平面感应电机具有集成度高、空间体积小、运动灵活多变等优点,在需要全向驱动的场合已得到应用,有着重要的研究意义和发展前景。主要介绍了多自由度平面感应电机的研究现状,对几种多自由度平面感应电机的结构及各自的工作原理和特点展开分析,指出了多自由度平面感应电机在现研究阶段存在的缺点和不足,并提出了一些性能优化方法,探讨了多自由度平面感应电机在未来的发展前景及趋势。

关键词: 平面电机, 感应电机, 多自由度, 拓扑结构, 优化方法

Abstract:

The planar induction motor has the advantages of simple structure, convenient manufacture, high flexibility of movement, which has been applied in certain industrial applications. The research status of the multi DOF planar induction motors was presented. The structures, corresponding working principle and characteristics of several multi DOF planar induction motors were discussed. There are some shortcomings and deficiencies in the present multi DOF planar induction motors, which should be overcome. Some performance optimization methods were developed. The research priorities, studied direction and grown tendency about the motor were pointed.

Key words: planar motor, induction motor, multi-DOF, topological structure, optimization method

中图分类号:

TM346

吴伟, 司纪凯, 岳帅军, 刘群坡, 封海潮, 李应生. 多自由度平面感应电机发展综述[J]. 微特电机, 2018, 46(8): 88-92.

WU Wei, SI Ji-kai, YUE Shuai-jun, LIU Qun-po, FENG Hai-chao, LI Ying-sheng. An Overview on Development of Multi-Degree-of-Freedom Planar Induction Motor[J]. Small & Special Electrical Machines, 2018, 46(8): 88-92.

参考文献

[1]	寇宝泉, 张鲁, 李立毅 , 等. 平面电动机技术发展综述[C]// 中国西安微特电机技术创新与发展论坛, 2010: 66-72.
[2]	杨金明, 吴捷, 张宙 , 等. 平面电动机的现状及发展[J]. 微特电机, 2003,31(6):31-34.
[3]	寇宝泉, 张赫, 潘东华 , 等. 平面电动机的发展现状[J]. 微特电机, 2011,39(2):67-71.
[4]	FUJII N, FUJITAKE M . Two-dimensional drive characteristics by circular shaped motor[J]. IEEE Transactions on Industry Applications, 1999,35(4):803-809.
[5]	DITTRICH P, RADECK D. 3-DOF Planar Induction Motor [C]//2006 IEEE International Conference on Electro/Information Technology.IEEE, 2006: 81-86.
[6]	KUMAGAI M, HOLLIS R L. Development and control of a three DOF Planar induction motor [C]//2012 IEEE International Conference on Robotics and Automation (ICRA).IEEE, 2012: 3757-3762.
[7]	潘剑飞, 曹广忠, 张宙 . 平面电机设计与控制[M]. 北京: 科学出版社, 2011,6.
[8]	王文成 . 平面感应电机研究与其开拓展望[J]. 山东矿业学院学报, 1992(1):55-62.
[9]	上海工大 , 上海电机厂.直线异步单机[M]. 北京: 机械工业出版社, 1979.
[10]	钟声, 申群太 . 单边直线感应电机边端效应的补偿及控制[J]. 采矿技术, 2008,8(1):66-68.
[11]	LAPORTE B, TAKORABET N, VINSARD G . An approach to optimize winding design in linear induction motors[J]. IEEE Transactions and Magnetics, 1997,33(2):1844-1847.
[12]	MISHIMA T, HIRAOKA M, NOMURA T. A study of the optimum stator winding arrangement of LIM in maglev systems [C]//IEEE International Conference on Electric Machines & Drives.IEEE, 2005: 1238-1242.
[13]	ABDEL-KHALIK A S, AHMED S, MASSOUD A. A five-phase linear induction machine with planar modular winding [C]//IEEE International Conference on Inducstrial Technology.IEEE, 2015: 580-585.
[14]	COX T, EASTHAM J F. Multi layer planar concentrated windings [C]//IEEE International Electric Machines & Drives Conference (IEMDC).IEEE, 2011: 1439-1444.
[15]	EASTHAM J F, COX T, PROVERBS J . Application of planar modular windings to linear induction motors by harmonic cancellation[J]. Iet Electric Power Applications, 2010,4(3):140-148.
[16]	SHIRI A, SHOULAIE A . Design optimization and analysis of single-sided linear induction motor,considering all phenomena[J]. IEEE Transactions on Energy Conversion, 2012,27(2):516-525.
[17]	TREVISO F, SILVEIRA M A D, FLORES FILHO A F, et al.An induction planar actuator for surface inspection[J]. IEEE International Magnetics Conference (INTERMAG), 2015,51(11):1.
[18]	MAGILL M P, KREIN P T. Electric machines as metamaterials: Induction machine design using planar layer models [C]//Electric Machines & Drives Conference.IEEE, 2011: 890-895.
[19]	周庆生, 黄苏融, 张琪 , 等. 新型冷却结构超高精度平面电机定子温度场分析[J]. 中国电机工程学报, 2012,32(15):134-139.
[20]	GESSESE Y, BINDER A. Design and analysis of specific high-speed solid rotor induction motor with copper end rings [C]//IEEE Conference on Electromagnetic Field Computation.IEEE, 2010: 1.

多自由度平面感应电机发展综述

An Overview on Development of Multi-Degree-of-Freedom Planar Induction Motor

RichHTML

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

联系我们

[1]	杨颖, 邓江明, 吕刚. 短定子超导直线感应电机性能研究[J]. 微特电机, 2021, 49(2): 7-10.
[2]	周银萍, 赵镜红, 程海军, 马远征. 基于MSC的五相感应电机缺两相容错控制[J]. 微特电机, 2021, 49(2): 39-42.
[3]	刘路, 卜飞飞, 刘皓喆, 黄文新. 五相感应电机起动/发电系统起动控制研究[J]. 微特电机, 2020, 48(9): 34-38.
[4]	吕刚, 杨镜. 初级横向偏移时帽型次级直线感应电动机制动特性分析[J]. 微特电机, 2020, 48(6): 1-4.
[5]	熊义勇, 赵镜红. 小型五相感应电机设计及槽数选取分析[J]. 微特电机, 2020, 48(6): 28-32.
[6]	吕刚, 陈玫志, 杨镜, 曾迪晖, 周桐. 次级非中心位置工况双边直线电动机有限元分析[J]. 微特电机, 2020, 48(4): 28-31.
[7]	张利军, 崔晓光, 胡冰, 李刚. 基于龙伯格观测器的变频一体机谐波电流抑制控制[J]. 微特电机, 2020, 48(4): 55-59.
[8]	杨玺, 叶伟玲, 汤铭华, 陈子辉, 冯君璞, 严柏平, 殷豪. 谐波影响下的三相感应电机效率研究[J]. 微特电机, 2020, 48(3): 29-32.
[9]	李楷然, 刘永强, 吴立泉, 梁兆文. 一种感应电机转子断条故障建模方法[J]. 微特电机, 2020, 48(3): 33-37.
[10]	胡冰,张利军,崔晓光,咸粤飞. 基于改进电压模型的感应电机无速度传感器矢量控制[J]. 微特电机, 2020, 48(2): 34-37.
[11]	黄家杰, 刘永强, 吴立泉, 梁兆文. 一种感应电机机械故障建模方法及故障度辨识[J]. 微特电机, 2020, 48(10): 11-15.
[12]	李良, 宋文乐, 张树亮, 蒋曦, 王朝阳, 赵俊蕾, 李鹏宇. 基于蒙特卡罗法的感应电机转子槽数及转速辨识方法[J]. 微特电机, 2020, 48(10): 16-19.
[13]	李永佳, 郑晓钦. 九相感应电机切套运行的非线性磁路计算[J]. 微特电机, 2020, 48(10): 20-23.
[14]	. 基于ANSYS的高速感应电机设计[J]. 微特电机, 2020, 48(1): 34-38.
[15]	. 电动汽车用六相感应电机开路故障容错控制[J]. 微特电机, 2020, 48(1): 44-48.